Email:ryker@evosyncs.com

X360RUN Glitcher Board 96MHZ Crystal Oscillator w/ Slim Cable for All XBOX360 Slim

SKU: RWMOX196

Comments or Messages

Description

X360Run Perfectly carcks XBOX360 slim
X360Run Glitcher Board Instruction (SLIM Trinity10.83A/9.6A)
It is perfectly compatible with all XBOX360 Slim machine
It used the high performance and high frequency pulse-attack chip
It has the more precisely pulse-attack boot time in an instant.
It is comprehensive to upgrade and replace the Matrix Glitcher and Xecuter Coolrunner Glitcher Board.

Main
Support Corona and Trinity slim machine.
High Performance of the pulse-attack chip, the working frequency can reach at 96MHz, the more precisely pulse-attack, and can be refined to adjust the attacking parameter.
So far the least external components, using the high quality components to manufacture,perfect design and high reliability
So far the Minimum PCB size, easily to install and fix
So far the most simple installation and debugging, with the two pulse single line with 4-7cm
By jumping the wire to make it short, yon can have machine selection and parameter adjustment ,it does not need to program by software.
Boot time almost in 30 seconds.

X360Run Glitcher Board Instruction(SLIM Trinity10.83A/9.6A)
.The theory of X360Run Glitcher Board

The X360Run send out a confirm width of pulse to XBOX360 slimmachine. For different type XBOX360 slim machine have different type pulse time point and width.

.The X360Run Glitcher Board and trimming switch:

.Configuration and trimming

The user must choose a different configuration options according to the different type XBOX360 slim machine.

The user can use the factory default setting of the X360RunGlitcher board.however,because of components and wire materials may have little differences, different batch XBOX360 machine and X360RunGlitcher board are also little differences,the user can use the trimmability switch to get a better time pulse,and this change will make XBOX360 machine achieve the best effective.

X360Run Glitcher board have four type switch and trimmingadjustable setting:
(S: short the jumper pad , O:open the jumper pad)
1. The XBOX360 slim machine type selection setting

set the jumper pad M0=S,M1=S,M2=0. The value of capacitors about CD=220P and CO=25P.
2. Pulse time delay trimming setting

Trinity 9.6A/10.83Aset the jumper pad D0=O,D1=S,D2=S
3. Pulse width trimming setting

set the jumper pad W0=S,W1=O,W2=O
4. The adjustment of resistance and capacitance in the pulse signal output

The D pin of X360Run Glitcher board is pulse signal output, can reduce the pulse signal strength by series resistance, the factory default value is 8.2.

The D pin of X360Run Glitcher board is pulse signal output, can produce an effect on launch XBOX360 slim machine succeed by shunt-wounddifferences value of Monolithic capacitance, the factory default value

is CD=220pf(Trinity),The length of two pins about CD capacitance don’t cut to short(The length of CD capacitance about 1.5cm-1.7cm),and CO=25P.

Attention!: if replace Monolithic capacitance,must weld the new Monolithic capacitance complete before launch XBOX360 slim machineagain.
5.Wire Install

X360Run Glitcher board have SIX wire to be connected,them are:

1. Power Wire: VDD,

2. Ground Wire: GND,

3. I2C_SCL(E),

4. I2C_SDA(F),

5. POST_OUT(C),

6. CPU_RST(D)
For Trinity 9.6A
The 14 Wire direct connect to Glitcher board,about 10cm
The 5-6 Wire direct connect to Glitcher board,about 4cm to 7cm.canadjustment the length of 5-6 Wire in 4cm to 7cm carefully,then get the best effect.

For Trinity 10.83A

The 14 Wire direct connect to Glitcher board,about 10cm
The 5-6 Wire direct connect to Glitcher board,about 4cm to 7cm.canadjustment the length of 5-6 Wire in 4cm to 7cm carefully,then get the best effect.
Attention!:

After modify the Xbox360 Trinity 10.83A machine,Must open and close 10 times to 20 times to check Whether or not Red-led on panel is Lights up.if Red-led is Lights up,Can connect D point to GND point on X360Run PCB Board with a 10K-20K metal-wire Resistor.
.The weld of changed XBOX360 slim machine

1. TRINITY

. Debug and install

U_C”to wire

U_D”toD” wire

The shunt-wound Monolithic capacitance CD [330pf(Corona) or 220pf(Trinity)],one pin weld to C1 point, another pin weld to a point between D point and C2 point.

The length of two pins about CD capacitance don’t cut to short.
Item:

1* X360RUN Glitcher Board 96MHZ Crystal Oscillator w/ Slim Cable for All XBOX360 Slim

Additional information

Weight 0.008 kg
Dimensions 5 × 3.5 × 0.8 cm
Condition

Original

Reviews

There are no reviews yet.

Be the first to review “X360RUN Glitcher Board 96MHZ Crystal Oscillator w/ Slim Cable for All XBOX360 Slim”

Your email address will not be published. Required fields are marked *

Related Products

Categories

Filter by price

Filter by color