Email:ryker@evosyncs.com

New RGH X360RUN 1.1 Glitcher Red Board with 96MHZ Crystal Oscillator for XBOX360 Slim

SKU: RWMOX200

Comments or Messages

Description

High Light:

NEW RGH X360RUN 1.1 version PCB same STONE USE
Use for xbox360 Toshiba nand is fast
Note:
Red Board(X360Run1.1)
be fit for Corona(Include the Xbox360 machine produced after Nov. 2013 and Corona machine of Toshiba NandFlash on board)
Attention:The Xbox360 machine of Windbond memory on board,produced after Nov. 2013,need change the Windbond memory chip first.
X360Run Perfectly carcks XBOX360 slim
X360Run Glitcher Board Instruction (SLIM + Trinity10.83A/9.6A)
It is perfectly compatible with all XBOX360 Slim machine
It used the high performance and high frequency pulse-attack chip
It has the more precisely pulse-attack boot time in an instant.
It is comprehensive to upgrade and replace the Matrix Glitcher and Xecuter Coolrunner Glitcher Board.

Main
Support Corona and Trinity slim machine.
High Performance of the pulse-attack chip, the working frequency can reach at 96MHz, the more precisely pulse-attack, and can be refined to adjust the attacking parameter.
So far the least external components, using the high quality components to manufacture,perfect design and high reliability
So far the Minimum PCB size, easily to install and fix
So far the most simple installation and debugging, with the two pulse single line with 4-7cm
By jumping the wire to make it short, yon can have machine selection and parameter adjustment ,it does not need to program by software.
Boot time almost in 30 seconds.
X360Run1.1 (Slim+Trinity) Glitcher Board Instruction
.The theory of X360Run Glitcher Board
The X360Run send out a confirm width of pulse to XBOX360 slimmachine. For different type XBOX360 slim machine have different typepulse time point and width.

.The X360Run Glitcher Board and trimming switch:

.Configuration and trimming
The user must choose a different configuration options accordingto the different type XBOX360 slim machine.
The user can use the factory default setting of the X360Run
Glitcher board.the user can use the trimmability switch to get abetter time pulse,and this change will make XBOX360 machine achievethe best effective.

Please choice default setting in the following three table,othersetting only for test by user choice.Please use rona Mode 1″ for
Corona machine of Toshiba NandFlash on board and produced after Nov.2013(need change the Windbond memory chip first).
The Corona Mode2 for test by user choice.
The Compatible and function of Corona X360run Yellow-Board Modesame as X360Run Yellow Board.
X360Run Glitcher board have four type switch and trimmingadjustable setting:
(S: short the jumper pad , O:open the jumper pad)

1. The XBOX360 slim machine type setting

XBOX360 Type
Timing pulse
M2
M1
M0
Monolithic
Capacitor CD
Ceramics
Capacitors CO
Command

Corona
forward
S
S
S
330P
15P
Corona
Mode 1

Corona
default
S
S
0
330P
15P

Corona
Add-ons
delay
S
0
S
330P
15P
Corona
Mode 2

Corona
default
S
0
0
330P
15P

Trinity10.83A
default
0
S
S
150P
20P
Compatible
X360Run
Yellow-Board
Mode

Trinity9.6A
default
0
S
0
220P
25P

Corona
Add-ons
delay
0
0
S
330P
15P

Corona
default
0
0
0
330P
15P

According to the different type XBOX360 machine , set the accordingM0,M1,M2 jumper pad with S or O follow this table. The value of capacitorsabout CD and CO must set correct too . the factory default value is CoronaMode 1:SSO.
2. Pulse time delay trimming setting

Delay trimming
D2
D1
D0
unit

0
S
S
-3

0
S
0
-2

0
0
S
-1

0
0
0
default

Corona Mode 1; Compatible X360Run Yellow-Board Corona Mode
S
S
S
+1

Trinity 10.83A
Trinity 9.6A
S
S
0
+2

Corona Mode 2
S
0
S
+3

S
0
0
+4

The pulse time can be adjust to forward(forth:-1~-3) orbackward(back:+1~+4) on the basis of the standard value.
According to the different type XBOX360 machine, set theaccording D0,D1,D2 jumper pad with S or O follow this table. thefactory default value is Corona Mode 1/X360Run Yellow-Board CoronaMode:SSS(+1).

3. Pulse width trimming setting

width trimming
W2
W1
W0
unit

0
S
S
-3

0
S
0
-2

Trinity 10.83A
0
0
S
-1

Trinity 9.6A Corona Mode 2
0
0
0
default

S
S
S
+1

Corona Mode 1; Compatible X360Run
Yellow-Board Corona Mode
S
S
0
+2

S
0
S
+3

S
0
0
+4

The pulse width can be adjust to forward(forth:-1~-3) or backward(back:+1~+4) on the basis of the standard value.
According to the different type XBOX360 machine, set the accordingW0,W1,W2 jumper pad with S or O follow this table. the factorydefault value is rona Mode 1/X360Run Yellow-Board ronaMode:SSO(+2).

4. The adjustment of resistance and capacitance in the pulse signal output
The D pin of X360Run Glitcher board is pulse signal output, canreduce the pulse signal strength by series resistance, the factorydefault value is 8.2.
The D pin of X360Run Glitcher board is pulse signal output, canproduce an effect on launch XBOX360 slim machine succeed by shunt-wounddifferences value of Monolithic capacitance, the factory default valueis CD=330pf(Corona),CD=220pf(Trinity9.6A) or CD=150pf(Trinity10.83A)
The length of two pins about CD capacitance don’t cut to short(The length of CD capacitance about 1.5cm-1.7cm).
Attention!: if replace Monolithic capacitance,must weld the newMonolithic capacitance complete before launch XBOX360 slim machineagain.

5.Wire Install
X360Run Glitcher board have SIX wire to be connected,them are:
1. Power Wire: VDD,
2. Ground Wire: GND,
3. I2C_SCL(E),
4. I2C_SDA(F),
5. POST_OUT(C),
6. U_RST(D)
For Corona and Trinity 9.6A
The 14 Wire direct connect to Glitcher board,about 10cm
The 5-6 Wire direct connect to Glitcher board,about 4cm to 7cm.canadjustment the length of 5-6 Wire in 4cm to 7cm carefully,then get thebest effect.

For Trinity 10.83A

The 14 Wire direct connect to Glitcher board,about 10cm
The 5 Wire direct connect to Glitcher board,about 4cm to 7cm.canadjustment the length of 5 Wire in 4cm to 7cm carefully,then get thebest effect.
The 6 Wire direct connect to Glitcher board,about 4cm to 15cm(12cm istypical value).can adjustment the length of 6 Wire in 4cm to 15cmrefully,then get the best effect.

Attention!:
After modify the Xbox360 Trinity 10.83A machine,Must open and close10 times to 20 times to check Whether or not Red-led on panel is Lightsup.if Red-led is Lights up,Can connect D point to GND point on X360Run PCB Board with a 10K-20K metal-wire Resistor.

.The weld of changed XBOX360 slim machine
1. Corona-V1, Corona-V2

2. Corona-V3, Corona-V4,Corona-V5,Corona-V6
3.Trinity

. Debug and install
U_C”to wire
U_D”toD” wire
The shunt-wound Monolithic capacitance CD [330pf(Corona) or220pf(Trinity)],one pin weld to C1 point, another pin weld to a pointbetween D point and C2 point.
The length of two pins about CD capacitance don’t cut to short.

. Typical application
Corona Mode 1,be fit for Corona(Include the Xbox360 machine producedafter Nov. 2013 and Corona machine of Toshiba NandFlash on board)

XBOX360 Type
Timing pulse
M2
M1
M0

Corona
default
S
S
0

Delay trimming
D2
D1
D0
unit

S
S
S
+1

Width trimming
W2
W1
W0
unit

S
S
0
+2

Attention!:
The Xbox360 machine of Windbond memory on board, produced after Nov.2013,need change the Windbond memory chip first.

XBOX360 Type
Timing pulse
M2
M1
M0

Corona
default
S
0
0

Delay trimming
D2
D1
D0
unit

S
0
S
+3

Width trimming
W2
W1
W0
unit

0
0
0
default

Attention!:
The Xbox360 machine of Windbond memory on board,produced after Nov.2013,need change the Windbond memory chip first.

Compatible X360Run Yellow-Board Corona Mode,be fit for Corona(Notinclude the Xbox360 machine of Toshiba NandFlash on board and Corona of
change the Windbond memory chip first.)

XBOX360 Type
Timing pulse
M2
M1
M0

Corona
default
0
0
0

Delay trimming
D2
D1
D0
unit

S
S
S
+1

Width trimming
W2
W1
W0
unit

S
S
0
+2

Item:

1* New RGH X360RUN 1.1 Glitcher Red Board with 96MHZ Crystal Oscillator for XBOX360 Slim

Additional information

Weight 0.005 kg
Condition

OEM

Reviews

There are no reviews yet.

Be the first to review “New RGH X360RUN 1.1 Glitcher Red Board with 96MHZ Crystal Oscillator for XBOX360 Slim”

Your email address will not be published. Required fields are marked *

Related Products

Categories

Filter by price

Filter by color